March 28th, 2024 3:21PM EDT
1(888)626-4365

CUSTOM VARIATIONS

Part Numbering System for Standard Driver Custom Variations: LE PXX –XX –XX -Fxx
(DDPDX Part #) –(Custom Dash) –(Custom Dash) –F(Preset settings)
eg. LE PNX-50-22-F01-CSA = Standard LE PNX driver with 5amp Max (-50) with error detect pin (-22) custom factory parameters (-F01) with CSA certification.
We offer any combination of the below features unless otherwise stated. This part number system does not completely apply to ME**** custom products. Contact us for more details.
CONTACT US PDF COPY
Optional Features (List of Custom Variations)
-0025 : 25mA Max Ultra Low Current Valve Driver
DDPDX driver with 25mA max current
-01 : Driver Board only, no enclosure
DDPDX Sold without enclosure. PCB only
-01A : 100mA Max current output
DDPDX driver with 100mA max current
-02 : 200mA Max current output
DDPDX driver with 200mA max current
-03 : 300mA Max current output
DDPDX driver with 300mA max current
-04 : -5 to +5V Command Input
-5 to +5V Command Input
-06 : 600mA Max current output
DDPDX driver with 600mA max current
-07 : Driver with 20" Flying Leads
Wire leads soldered directly to driver, 20" leads, 18AWG wire (LE PGX green terminal removed).
-08 : NEMA 4X box with External Encoder Knobs
NEMA 4X box for LE PNX/LE PIX with Large External Encoder Knobs mounted on lid.
-09 : NEMA 4X box with POT and knob mounted on lid
NEMA 4X box for LE PNX/LE PIX with POT and knob mounted on lid.
-10 : 1.00A Max current output
DDPDX driver with 1.00A max current
-11 : Low profile power connector
Low profile power connector, Driver Board only, no enclosure.
-12 : 1.2A Max current output
DDPDX driver with 1.20A max current with resistor 0.25 Ohm.
-15 : 1.5A Max current output
DDPDX driver with 1.50A max current.
-16 : 1V to 6V input
1V to 6V input.
-19 : Digital Output Selection for A-B Solenoid Indicator
A dual driver that tells you whether you are on A or B side with a digital feedback read by the PLC.
-21 : Reverse Acting Driver
Driver with inverse output (negative gain). Low Command Signal will output HI current. High Command Signal will output LO current. Driver with reverse acting command control. Max command input will have a current output of minimum value, etc.
-22 : Error Detection Status Pin
Error Status Pin enables Hi when Error detected.
-23 : Fixed Input Setting
Permanently set to 0 to 5VDC, 0 to 10VDC, or 4 to 20mA mode.
-24 : 2 Digital Inputs - 4 Preset Output Levels
Two digital input with four output levels.
-31 : 0 to 20mA input
Driver has 0 to 20mA input mode option
-32 : 0 to 10mA input
Driver has 0 to 10mA input mode option
-33 : Low Frequency PWM
Lower than standard frequency PWM (20-200 Hz for DDPD X).
-34 : Low Frequency, Open Loop PWM
Open Loop Driver. Command Signal Driver by Duty Cycle Percentage
-35 : 4 Set Input Driver
Single Driver with four output levels.
-37 : Negative Gain Driver
Inverse Gain Driver with "Li" percentage parameter to cut the output current. Based on an LE PGX. Added function to cut the output current at a set percentage.
-40 : 4.00A Max current output
DDPDX driver with 4.00A max current
-50 : 5.00A Max current output
DDPDX driver with 5.00A max current
-70 : 7.00A Max current output
DDPDX driver with 7.00A max current
-BT : Wireless Controlled Driver
Bluetooth connection option allows user to monitor & adjust Lynch driver on their mobile device.
-CSA : CSA Certified Drivers
Field certified driver with Canadian Standards Association approval.
Lynch Headquarters Mississauga on map.
Canada
1799 Argentia Road
Mississauga, Ontario, L5N 3A2
Lynch Headquarters New York on map.
U.S.A.
3790 Commerce Court Suite 500,
North Tonawanda, New York, 14120